Teledyne Monitor Labs T200 for NO, NO2, NOx
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.
A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.
All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.
The Model T200 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
- Ranges: 0-50 ppb to 0-20 ppm, user selectable
- Selectable ranges, with dual range capability
- Large, vivid, and durable color graphics display with touch screen interface
- Ethernet, RS-232, and (optional) USB com ports
- Front panel USB connections for peripheral devices and firmware upgrades
- 8 analog inputs (optional)
- Adaptive signal filtering optimizes response time
- Temperature & pressure compensation
- Internal zero & span check (optional)
- Comprehensive internal data logging with programmable averaging periods
- Ability to log virtually any operating paramete
- Two-year warranty
| Ranges | Min: 0 – 50 ppb full scale Max: 0 – 20,000 ppb full scale (selectable, dual-range supported) |
| Measurement Units | ppb, ppm, μg/m3, mg/m3 (selectable) |
| Zero Noise | < 0.1 ppb (RMS) |
| Span Noise | < 0.2% of reading (RMS) above 50 ppb |
| Lower Detectable Limit | < 0.2 ppb |
| Zero Drift | < 0.5 ppb/24 hours |
| Span Drift | < 0.5% of full scale/24 hours |
| Response Time | < 80 seconds to 95% |
| Linearity | 1% of full scale |
| Precision | 0.5% of reading above 50 ppb |
| Sample Flow Rate | 500 cc/min ±10% |
| Power Requirements | 100V-120V, 220V-240V, 50/60 Hz, Typical power 110W |
| Analog Output Ranges | 10V, 5V, 1V, 0.1V (selectable) |
| Recorder Offset | ±10% |
| Included I/O | 1 x Ethernet: 10/100Base-T 2 x RS232 (300-115,200 baud) 2 x USB device ports 8 x opto-isolated digital outputs 6 x opto-isolated digital inputs 4 x analog outputs |
| Optional I/O | 1 x USB com port 1 x RS485 4 x digital alarm outputs Multidrop RS232 3 x 4 – 20mA current outputs |
| Operating Temperature Range | 5 – 40ºC (with US EPA Approval) |
| Dimensions (HxWxD) | 7” x 17” x 23.5” (178 x 432 x 597 mm) |
| Weight | Analyzer: 40 lbs (18 kg) External pump: 22 lbs (10 kg) |
| Certifications
Specifications are subject to change without notice.
All specifications are based on constant conditions.
|
US EPA: RFNA-1194-099 EU: EN14211 TÜV Rheinland QAL1 Certified: EN15267 MCerts: Sira MC050068/11 CNEMC: 质(认)字 No. 2015-028 Report |
The following table provides a list of items that need regular maintenance to ensure your product remains in good working condition.
| ITEM | ACTION | Frequency | Cal Check Required |
| TEST functions | Review and evaluate | Weekly | No |
| Particulate filter | Change particle filter | Weekly (if in stack system: As Needed) | No |
| Zero/span check | Evaluate offset and slope | Weekly | No |
| Zero/span calibration | Zero and span calibration | Every 3 months | Yes |
| External zero air scrubber option | Exchange chemical | Every 3 months | No |
| External dryer option | Replace chemical | When indicator color changes | No |
| Ozone cleanser | Change chemical | Annually | Yes |
| Reaction cell window (“optical filter” Figure 11‑6 in manual) | Clean | Annually or as necessary | Yes |
| DFU filters | Change particle filter | Annually | No |
| Pneumatic sub-system | Check for leaks in gas flow paths | Annually or after repairs involving pneumatics | Yes if a leak is repaired |
| Reaction cell O-rings & sintered filters | Replace | Annually | Yes |
| PMT Sensor Hardware Calibration | Low-level hardware calibration | On PMT/ preamp changes or if slope is outside of 1.0±0.3 | Yes |
| Pump | Rebuild head | when RCEL pressure exceeds 10 in-Hg-A (at sea level) | Yes |
| Inline Exhaust Scrubber | Replace | Annually | No |
| NO2 converter | Replace converter | Every 3 years or if conversion efficiency drops below 96% | Yes |
| Desiccant bags | Replace | Any time PMT housing is opened for maintenance | n/a |